top of page
ROBUS
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Practical: control unit and optional PS124 buffer batteries can be connected by means of practical guided - connector.
Advanced: RB400, RB600 and RB1000 are equipped with a temperature sensor: adapt the motor power to the climatic conditions and at the same time thermal cutout. A master/slave selection automatically synchronises two motors. This means it is possible to automate 2-leaf sliding gates set opposite each other.
Intelligent: thanks to the obstacle detection system and automatic programming of the working times. Self-diagnosis by means of a flashing light. 8 programming levels.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Sturdy: base and release in pressure die cast with easy to open handle.
Silent: gear motor on bearings.
ROBUS 400 600 1000
NICE - For sliding gates weighing up to 400 kg (RB400), up to 600 kg (RB600) and up to 1000 kg (RB1000).
Versions with electromechanical limit switch (RB400/RB600/RB1000) and with inductive limit switch (RB600P/RB1000P).
ROBUSKIT 400 BD
NICE - For sliding gates weighing up to 400kg.
Kit contains:
1x RB400 - 1 Irreversible electromechanical gearmotor, with built-in control unit and OXIBD bidirectional radio receiver with connector for connection via Nice BlueBUS.
2x ON3EBD - 2 Transmitters 433.92 MHz, 3 channels, bidirectional.
1X EPMB - 1 Couple of external photocells designed for connection by Nice BlueBUS.
1X ELAC - 1 LED flashing light with integrated aerial.
1X TS - 1 Signboard.
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Practical: control unit and PS124 buffer battery (optional) can be connected by means of a simple connector and can be housed directly inside Robus.
Advanced: RB400 is equipped with a temperature sensor: adapt the motor power to the climatic conditions and at the same time thermal cut-out. A master/slave selection automatically synchronises two motors. This means it is possible to automate 2-leaf sliding gates set opposite each other.
Intelligent: thanks to the obstacle detection system and automatic programming of the working times. Self-diagnosis by means of a flashing light. 8 programming levels.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Sturdy: base and release in pressure die cast with easy to open handle.
Silent: gear motor on bearings.
ROBUSKIT 600 BD
Nice - For sliding gates weighing up to 600kg.
Kit contains:
1x RB600 - 1 Irreversible electromechanical gearmotor, with built-in control unit and OXIBD bidirectional radio receiver with connector for connection via Nice BlueBUS.
2x ON3EBD - 2 Transmitters 433.92 MHz, 3 channels, bidirectional.
1X EPMB - 1 Couple of external photocells designed for connection by Nice BlueBUS.
1X ELAC - 1 LED flashing light with integrated aerial.
1X TS - 1 Signboard.
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Practical: control unit and PS124 buffer battery (optional) can be connected by means of a simple connector and can be housed directly inside Robus.
Advanced: RB600 is equipped with a temperature sensor: adapt the motor power to the climatic conditions and at the same time thermal cut-out. A master/slave selection automatically synchronises two motors. This means it is possible to automate 2-leaf sliding gates set opposite each other.
Intelligent: thanks to the obstacle detection system and automatic programming of the working times. Self-diagnosis by means of a flashing light. 8 programming levels.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Sturdy: base and release in pressure die cast with easy to open handle.
Silent: gear motor on bearings.
NAKED SLIDING
NAKED SLIDING 400
Nice concealed motor for sliding gates up to 400Kg
with leaf lengths up to 6m
Its extremely small size allows the motor to be installed even in very slender posts, with interior size down to 140x140 mm.
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Master/slave selection: for automatic synchronisation even of 2 motors, allowing automation of sliding gates with two opposing leaves. Intelligent: thanks to obstacle detection and automatic working time programming. Self-diagnostics with flashing light signalling.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Simple and precise limit switch adjustment: integral absolute limit switch, quick learning with just one opening or closing operation with motor released.
Practical: control unit and optional PS124 buffer batteries can be connected by means of practical guided - connector.
Flexible: unlocking can be provided on both sides of the post and/or on the outside (with the KIO and KA1 accessories). Also easy to install on existing posts.
https://static.wixstatic.com/media/ad9cc9_074d3b3a0168459b94e0d1b838f932ab~mv2.jpg
Motor with built-in control unit and absolute encoder which can be installed inside a compact post with suitable holes.
SLIGHT
SLIGHT
Nice motor for sliding gates up to 400kg with leaf length up to 6m.
Innovative ultra-compact design: the vertical configuration of the motor makes it easy to install even in narrow openings.
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Built-in LED light: programmable as either a flashing or courtesy light, it warns of gate movement during opening and closing.
Master/slave selection: for automatic synchronisation even of 2 motors, allowing automation of sliding gates with two opposing leaves.
Intelligent: thanks to obstacle detection and automatic working time programming. Self-diagnostics with flashing light signalling.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Built-in absolute limit stop:
• simple and precise regulation thanks to the rapid learning in a single movement with the motor released;
• no bracket or accessory to be installed on the ratchet;
• particularly suitable in snow areas.
Practical: control unit and optional PS124 buffer batteries can be connected by means of practical guided - connector.
Motor with built-in control unit and absolute encoder.
RUN
RUN 1500
NICE - For sliding gates weighing up to 1500kg.
User-friendly: thanks to the BlueBUS system, allowing the control unit to be connected to up to 7 pairs of photocells and control, security and signalling devices with just two wires.
Practical: the control unit and PS124 buffer battery (optional) can be connected by means of a simple connector and can be housed directly inside the motor.
Advanced: the temperature sensor adapts the motor force to weather conditions, setting the thermal cut-out protection accordingly; a master/slave selection automatically
synchronises 2 motors, enabling the automation of sliding gates with two opposing leaves.
Intelligent: thanks to the obstacle detection system and automatic programming of the working times. Self-diagnosis by means of a flashing light. 8 programming levels.
Safe: acceleration and deceleration can be adjusted at the beginning and at the end of each opening and closing manoeuvre.
Sturdy: base and release in pressure die cast with easy to open handle.
Silent: gear motor on bearings.
Versions with electromechanical limit switch (RUN1500) and with inductive limit switch (RUN1500P).
RUN 1800 2500
NICE - For sliding gates weighing up to 1800 kg (RUN1800) and up to 2500 kg (RUN2500).
Easy to install: the BlueBUS system enables connections by means of just two wires between the control unit and up to 15 control safety and signalling devices.
Safe: the acceleration settings (at the start of the manoeuvre) and the deceleration settings (at the end of the manoeuvre) are precise and reliable.
Advanced temperature sensor: Run is able to manage force, adapting it to the different climatic and environmental conditions, while adapting the thermal cut-out protection and intensity of self-ventilation, depending on the temperature reading.
Master/slave selection: for automatic synchronisation even of 2 motors, allowing automation of sliding gates
with two opposing leaves.
Practical and functional: the control unit (and inverter on version RUN2500I), housed inside Run, can be simply connected by means of the practical connector
guide.
Silent: gear motor on bearings.
RUN2500I version with built-in inverter
Perfect movement: the inverter enables the power supply and drive of the 3-phase motor with single-phase
current at 230 Vac, acting on the frequency to adjust speed of the automation from a minimum of 8.2 m/min to maximum 15.4 m/min. In the automation deceleration phase, the inverter, which dialogues with the control unit, increases the torque, thus improving performance and reducing the risk of the automation blocking on impact with obstacles.
bottom of page